Mercedes Benz XentryAuto Repair Technician Home

Setup-Connection-Between-DTS-Monaco-and-MB-SD-C4-DoIP-15

How to Setup Connection Between DTS Monaco and MB SD C4 DoIP

September 8, 2020 auto 0

After Benz DTS Monaco software installation,you need configure DTS Monaco for interface (here take MB SD C4 DoIP as example).So here car-auto-repair.com show you guide […]

How to Solve Benz Xentry “2221-45 No access authorization” Error

August 2, 2020 auto 0

When you running Mercedes Benz Xentry diagnostic software,you may find it give you a error [2221-45] No access authorization for XENTRY Diagnosis was found on […]

How to Fix Benz Xentry Missing Pictures Problem

July 25, 2020 auto 0

After finish Mercedes Benz Xentry.OpenShell.XDOS installation and activation,then running the software,you will find the Xentry missing cars pictures.So here car-auto-repair.com show you guide on how […]

How to Use XENTRY Advanced KeyGen to Activate Benz Xentry 2020

June 25, 2020 auto 0

XENTRY Advanced KeyGen is activator for Mercedes Benz Xentry diagnostic software.It can activate 2018/2019/2020 version Xentry diagnostic software.With this activator you can install and activate […]

This article show you procedures on DAS Xentry perform Central Gateway offline coding for Mercedes Benz E211.And i wrote Benz module coding projects here:Benz coding,check it to get more tests. Preparations: Benz DTS Monaco Software Free Download How to Install Mercedes Benz DTS Monaco Software VXDIAG Benz/BMW Central Gateway Offline Coding by DAS Xentry: Run Benz DAS Xentry diagnosis software 1 After vehicle identification and data reading,select “Quick Test”,then click “F3” 2 Wait for all modules data determined... 3 4 Note:It was not possible to automatically read all the values and they must therefore be entered manually. After all control units quick test finish,select “CGW-Central gateway”and click “F3” button to continue 5 Select “Control unit adaptations”,then click “F3” button 6 Select “Control module programming”,F3 to continue 7 In the following procedure,the data of the following modules is programmed in full: -Central gateway -System diagnosis -ASSYST -ASSYST PLUS Note:Sufficient voltage must be available throughout the procedure. Click “F2” 8 Select “Offline (diagnostic unit not networked)”,click “F3” to continue The measures to be performed on the vehicle can be supported using the online network connection to the central system or offline. The “online” process is always recommended. This ensures that the diagnostic system operates with the current data. If a network connection is not available,the “offline” process can be used 9 Data record selection Control module programming 10 New control unit software versions are available for the following control units: Control unit Central gateway Estimated programming duration:2 Minutes Perform control unit programming? Click “Yes” to continue 11 Enter the reason for control unit programming:up Click “F2” to continue 12 The coding is being read,please wait... 13 It will reset control unit to original delivery status 14 Rest of control module is performed. 15 Control unit Central gateway programming progress,it will take about 2 minutes Check the notes: 16 17 The coding is being carried out,please wait 18 Erase fault memory,please switch on ignition 19 Central Gateway programming was completed successfully All input fields must be filled out,then click “F2” to continue 20 Done!

Benz E211 Central Gateway Offline Coding by DAS Xentry

July 30, 2019 auto 0

This article show you procedures on DAS Xentry perform Central Gateway offline coding for Mercedes Benz E211.And i wrote Benz module coding projects here:Benz coding,check […]

Benz W205 Motor Electronics MED40 Coding by Xentry (2)

Benz 205 Motor Electronics MED40 Coding by Xentry

July 14, 2019 auto 0

This post show the procedures of how to use Benz Xentry diagnosis software to coding motor electronics MED40 for Mercedes Benz 205. Preparations: Newest […]

Mercedes Benz W205 Audio 20 Module Coding by Benz Xentry (2)

Mercedes Benz 205 Audio 20 Module Coding by Benz Xentry

July 11, 2019 auto 0

This instruction show you the guide on how to use Xentry diagnostic software to do Audio 20 module coding for Mercedes Benz 205. Reparations: […]

DAS Xentry Diagnose for Mercedes Benz Antos 963 Truck

July 1, 2019 auto 0

Here show you a test report on how to use DAS Xentry Diagnose software to diagnose Mercedes Benz Antos 963 truck. Related Contents: Mercedes-Benz […]

12.2020 Benz Xentry Diagnostic Software Installation & Activation Guide

November 14, 2018 auto 0

Here is a guide on how to install Xentry.Open.Shell 2020.Hope it helps! Note:Before installation,please go to BIOS setting to disable secure boot option for Windows […]

How to: XENTRY SCN Coding for Mercedes Benz S221

October 23, 2018 auto 0

SCN coding is also required to prevent any aftermarket enhancements that are done to improve the performance. If you want to install additional control module […]

Mercedes Benz Xentry 7,9 & 12/2014 Installation Guide

June 8, 2018 auto 0

This article show a guide on how to make a full installation for Mercedes Benz Xentry 7/2014 — 9/2014—12/2014.This guide made to be detailed and […]