Porsche Panamera 2013 Parking Brake Programming After Replacement by X431

This article show the guide on how to use Launch X431 to perform Parking brake replacement coding/programming.

 

Related Content:

Porsche Cayenne 2011 Brake Pad Matching After Replacement By Launch X431

Range Rover Evoque 2012 Parking Brake Pad Replacement Matching by Launch X431

How to Tell If You Need to Change Your Car Brake Pads

 

Procedures:

Build connection between Porsche Panamera and Launch X431,then enter the menu to select Porsche v21.81

Porsche Panamera 2013 Parking Brake Programming After Replacement by X431

Select “Automatically Search”

Porsche Panamera 2013 Parking Brake Programming After Replacement by X431

Then it will show the vehicle information as below:

VIN:WP0AA2A79DL010228

Year:2013

Vehicle:Panamera

Porsche Panamera 2013 Parking Brake Programming After Replacement (3)

Select “System Selection”

Select “Parking Brake”

Porsche Panamera 2013 Parking Brake Programming After Replacement (4)

Select “Special Function”

Select “Maintenance index”

Then it will show the procedures to replace the brake pad as below:

Porsche Panamera 2013 Parking Brake Programming After Replacement (5)

Please replace the brake pad according to the maintenance index,select “OK” to continue

Select “Put hand brake pad to installation position”

Porsche Panamera 2013 Parking Brake Programming After Replacement (6)

Follow the Launch X431 to operate:

Turn on the ignition switch and do not start the engine

Release the electronic hand brake

Porsche Panamera 2013 Parking Brake Programming After Replacement (7)

It will prompt that success to operate,select “OK” to next step

Porsche Panamera 2013 Parking Brake Programming After Replacement (8)

Select “Check basic setting of parking-brake”

Porsche Panamera 2013 Parking Brake Programming After Replacement (9)

The it will show the preparations of vehicle status:

Vehicle must stand on a level surface

The park brake is automatically applied and released

Note:The <Check basic setting of Parking brake> function enables the current setting status of the Parking brake to be determined and the required measures to be displayed.

Porsche Panamera 2013 Parking Brake Programming After Replacement (10)

Select “Next”,check the actuator air gap

Note:The standard air gap of Porsche range from 1.9mm to 2.4mm

Porsche Panamera 2013 Parking Brake Programming After Replacement (11)

Please check the basic setting of parking-brake select “OK”

Porsche Panamera 2013 Parking Brake Programming After Replacement (12)

Select “Grinding-in”

Grinding-in the parking brake

The grinding procedure for the parking brake is repeated eight times in sequence in the following steps.Each individual cycle must be completed successfully in order to put the parking brake into operation reliably.

 

The vehicle must be at standstill at the beginning of the grinding procedure.After pressing [OK] Start promptly accelerate the vehicle to 10-20 km/h (6-12mph) over a distance of approx 15-30m (50-100ft)

 

One signal tone is a prompt to start driving and another signal tone is prompt to stop the drive

 

The vehicle is brought to a standstill again after the end of the drive.The brake is released.A signal tone is a prompt to move the vehicle to position again in order to perform another grinding procedure

 

Eight grinding procedures are required in total in order to put the parking brake into operation.

Do not drive on public roads!

Please switch the hazard warning lights on for the duration of the test.

Porsche Panamera 2013 Parking Brake Programming After Replacement (13)

After operating 8 times,the X431 will inform that the Grinding-in is succeed and write it into the control unit.

Porsche Panamera 2013 Parking Brake Programming After Replacement (14)

 

Repeat

After final procedure,it will show you wait about 20 seconds

Writing the grinding-in state into the control unit…

It prompt that parking brake ground in successfully,select “OK” to continue

Select “Calibration”

Porsche Panamera 2013 Parking Brake Programming After Replacement (19)

Press “OK”,it will perform calibration function

Porsche Panamera 2013 Parking Brake Programming After Replacement (20)

Done!

 

Porsche Panamera2013 Parking Brake Programming After Replacement Video Guide:

Visited 1 times, 1 visit(s) today