Benz Coding Archives - Page 4 of 4 - Auto Repair Technician Home

Mercedes Benz Comand NTG4 Coding by DTS Monaco

November 30, 2019 auto 0

This instruction show you guide on how to use DTS Monaco to code Mercedes Benz Comand NTG4. Detail Coding Content List As Below: 1.CD […]

DTS Monaco Code for Benz Change Turn Signal Flasher from 3x to 5x

November 25, 2019 auto 0

In this instruction,i will show you guide on how to use DTS Monaco Coding for Mercedes change turn signal flasher from 3x to 5x and […]

Mercedes Benz 205 Complete Vehicle Coding by DTS Mocano

August 17, 2019 auto 0

This article show you how to use DTS Mocano perform Complete Vehicle Coding for Mercedes Benz 205 coding.And for more coding projects,check here:Benz Coding […]

This article show you procedures on DAS Xentry perform Central Gateway offline coding for Mercedes Benz E211.And i wrote Benz module coding projects here:Benz coding,check it to get more tests. Preparations: Benz DTS Monaco Software Free Download How to Install Mercedes Benz DTS Monaco Software VXDIAG Benz/BMW Central Gateway Offline Coding by DAS Xentry: Run Benz DAS Xentry diagnosis software 1 After vehicle identification and data reading,select “Quick Test”,then click “F3” 2 Wait for all modules data determined... 3 4 Note:It was not possible to automatically read all the values and they must therefore be entered manually. After all control units quick test finish,select “CGW-Central gateway”and click “F3” button to continue 5 Select “Control unit adaptations”,then click “F3” button 6 Select “Control module programming”,F3 to continue 7 In the following procedure,the data of the following modules is programmed in full: -Central gateway -System diagnosis -ASSYST -ASSYST PLUS Note:Sufficient voltage must be available throughout the procedure. Click “F2” 8 Select “Offline (diagnostic unit not networked)”,click “F3” to continue The measures to be performed on the vehicle can be supported using the online network connection to the central system or offline. The “online” process is always recommended. This ensures that the diagnostic system operates with the current data. If a network connection is not available,the “offline” process can be used 9 Data record selection Control module programming 10 New control unit software versions are available for the following control units: Control unit Central gateway Estimated programming duration:2 Minutes Perform control unit programming? Click “Yes” to continue 11 Enter the reason for control unit programming:up Click “F2” to continue 12 The coding is being read,please wait... 13 It will reset control unit to original delivery status 14 Rest of control module is performed. 15 Control unit Central gateway programming progress,it will take about 2 minutes Check the notes: 16 17 The coding is being carried out,please wait 18 Erase fault memory,please switch on ignition 19 Central Gateway programming was completed successfully All input fields must be filled out,then click “F2” to continue 20 Done!

Benz E211 Central Gateway Offline Coding by DAS Xentry

July 30, 2019 auto 0

This article show you procedures on DAS Xentry perform Central Gateway offline coding for Mercedes Benz E211.And i wrote Benz module coding projects here:Benz coding,check […]

Benz W205 Motor Electronics MED40 Coding by Xentry (2)

Benz 205 Motor Electronics MED40 Coding by Xentry

July 14, 2019 auto 0

This post show the procedures of how to use Benz Xentry diagnosis software to coding motor electronics MED40 for Mercedes Benz 205. Preparations: Newest […]

Mercedes Benz W205 Audio 20 Module Coding by Benz Xentry (2)

Mercedes Benz 205 Audio 20 Module Coding by Benz Xentry

July 11, 2019 auto 0

This instruction show you the guide on how to use Xentry diagnostic software to do Audio 20 module coding for Mercedes Benz 205. Reparations: […]

How to: XENTRY SCN Coding for Mercedes Benz S221

October 23, 2018 auto 0

SCN coding is also required to prevent any aftermarket enhancements that are done to improve the performance. If you want to install additional control module […]