Auto Repair Technician Home

How to Solve Ford Passive Anti Theft System PATS Trouble Codes

How to Program New PATS Key for Ford Manually

August 1, 2019 auto 0

This instruction show how to program a new PATS key for Ford vehicle.Note,you need try this procedures at your own risk.Car-auto-repair.com is not responsible for damage caused […]

How to Use Zed-Full Program Keys for Fiat Egea by OBD

July 31, 2019 auto 0

This article show you the guide on how to use Zed-Full immobilizer solution to program Fiat Egea keys by OBD. Procedures: Connect Zed-Full to Fiat […]

Volvo PTT Perform A Fuel Consumption Data Test

July 31, 2019 auto 0

This article show a guide on how to use Volvo PTT to perform a fuel consumption data test.And for more Volvo PTT projects,check here:Volvo Premium […]

Newest XPROG v5.84 Software Free Download

Newest XPROG 6.12 5.84 Software Free Download & Installation Guide

July 30, 2019 auto 0

What is XPROG? XPROG is a programmer used for read and write data for controller chip,include erial EEPROM’s, Microcontrollers (MCU), Electronics Control Units (ECU), DashBoards, […]

This article show you procedures on DAS Xentry perform Central Gateway offline coding for Mercedes Benz E211.And i wrote Benz module coding projects here:Benz coding,check it to get more tests. Preparations: Benz DTS Monaco Software Free Download How to Install Mercedes Benz DTS Monaco Software VXDIAG Benz/BMW Central Gateway Offline Coding by DAS Xentry: Run Benz DAS Xentry diagnosis software 1 After vehicle identification and data reading,select “Quick Test”,then click “F3” 2 Wait for all modules data determined... 3 4 Note:It was not possible to automatically read all the values and they must therefore be entered manually. After all control units quick test finish,select “CGW-Central gateway”and click “F3” button to continue 5 Select “Control unit adaptations”,then click “F3” button 6 Select “Control module programming”,F3 to continue 7 In the following procedure,the data of the following modules is programmed in full: -Central gateway -System diagnosis -ASSYST -ASSYST PLUS Note:Sufficient voltage must be available throughout the procedure. Click “F2” 8 Select “Offline (diagnostic unit not networked)”,click “F3” to continue The measures to be performed on the vehicle can be supported using the online network connection to the central system or offline. The “online” process is always recommended. This ensures that the diagnostic system operates with the current data. If a network connection is not available,the “offline” process can be used 9 Data record selection Control module programming 10 New control unit software versions are available for the following control units: Control unit Central gateway Estimated programming duration:2 Minutes Perform control unit programming? Click “Yes” to continue 11 Enter the reason for control unit programming:up Click “F2” to continue 12 The coding is being read,please wait... 13 It will reset control unit to original delivery status 14 Rest of control module is performed. 15 Control unit Central gateway programming progress,it will take about 2 minutes Check the notes: 16 17 The coding is being carried out,please wait 18 Erase fault memory,please switch on ignition 19 Central Gateway programming was completed successfully All input fields must be filled out,then click “F2” to continue 20 Done!

Benz E211 Central Gateway Offline Coding by DAS Xentry

July 30, 2019 auto 0

This article show you procedures on DAS Xentry perform Central Gateway offline coding for Mercedes Benz E211.And i wrote Benz module coding projects here:Benz coding,check […]

How to Initialize Nissan TEANA Window and Sunroof Configuration

July 29, 2019 auto 0

In this article www.car-auto-repair.com will show you how to initialize window control module and sunroof for Nissan TEANA.And for more Nissan topic,check here:Nissan Trouble Repair How […]

G-scan 2 Reset VANOS Adaptation Values for BMW 320I 2011 (3)

How to Use G-scan 2 Reset VANOS Adaptation Values for BMW 320I 2011

July 29, 2019 auto 0

This article show the test report of G-Scan2 perform resetting VANOS adaptation values for BMW 320I 2011.And for more G-scan2 diagnostic tool test report,check here:G-scan2 […]

MAN MANTIS EPC Electronic Parts Catalogue Free Download

July 28, 2019 auto 0

What is MAN MANTIS EPC? MAN MANTIS Electronic Parts Catalogue contains the complete information about spare parts for trucks, buses and various chassis of special assignment, and […]

VCP System Read Immobilizer PIN Code for EDC15P EDC16

July 28, 2019 auto 0

If you want to program new key,maybe you need to read out the PIN code,because when you program keys into immobilizer,you should enter the pin […]

Toyota Corolla 2013+ Keyless Go All Keys Lost Programming by Zed-Full

July 27, 2019 auto 0

This article show you guide on how to use Zed-Full perform all keys lost programming for Toyota Corolla 2013+ Keyless Go Keys. Procedures: Plug Zed-Full […]

International A26 Engine Change Oil Service Interval Overview

July 27, 2019 auto 0

General Overview: Change Oil Service Interval The Change Oil Service Interval feature provides a visual reminder to the operator that the oil change interval is soon […]