How to Disassemble & Assembling Cylinder for Still RX20 Forklift

This instruction show you guide on how to disassemble and assembling cylinder for Still RX20 forklift truck.

 

Related Contents:

STILL STEDS Forklift 8.19 8.18 2019 EPC & Diagnostics Free Download

 

Procedures:

Disassembling/assembling the outer cylinder
Disassembling the left-hand outer cylinder
– Pull the piston rod approx. 20 cm out of the cylinder pipe.
– Using protective jaws, clamp the piston rod in the vice.
– Unscrew the hydraulic adapter. The hydraulic adapter is secured with Loctite, so it may be necessary to gently heat the thread.
The next steps of the disassembly process are the same for both of the outer cylinders.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-1

Disassembling the left-hand and right-hand outer cylinder
– Using protective jaws, clamp the cylinder pipe loosely in the vice.
– Unscrew the cylinder head using a hook spanner. The cylinder head is secured with Loctite, so it may be necessary to gently heat the thread.
– Remove the cylinder head from the piston rod.
– Remove the set of seals.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-2

Assembling the outer cylinder
– Clean the cylinder head and check for signs of wear and damage.
– Insert a new set of seals into the cylinder head.
– Lightly coat the seals with hydraulic oil.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-3

– Check the piston rod and the chamfer for damage.
– Clean and degrease the thread on the cylinder pipe and cylinder head.
– Secure the thread by spreading three drops of Loctite 243 over the entire thread.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-4

– Attach the cylinder head and screw it on as far as it will go using a hook spanner. Secure the cylinder head by knocking the hook spanner with two blows of the hammer.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-5

 

Assembling the outer cylinder with hydraulic adapter
– Pull the piston rod approx. 20 cm out of the cylinder pipe.
– Using protective jaws, clamp the piston rod in the vice.
– Clean and degrease the thread in the cylinder pipe and hydraulic adapter.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-6

– Secure the thread by spreading three drops of Loctite 275 over the entire thread.
– Attach the hydraulic adapter and screw it on as far as it will go.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-7

 

Disassembling/assembling the middle cylinder
Disassembly
– Pull the piston rod approx. 20 cm out of the cylinder pipe.
– Using protective jaws, clamp the piston rod loosely in the vice.
– Unscrew the fork clevis. The fork clevis is secured with Loctite, so it may be necessary to gently heat the thread.
– Using protective jaws, clamp the cylinder pipe in the vice.
– Unscrew the cylinder head using a hook spanner. The cylinder head is secured with Loctite, so it may be necessary to gently heat the thread.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-8

– Remove the cylinder head from the piston rod.
– Remove the set of seals.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-9

Assembly
– Clean the cylinder head and check for signs of wear and damage.
– Insert a new set of seals into the cylinder head.
– Lightly coat the seals with hydraulic oil.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-10

– Check the piston rod and the chamfer for damage.
– Clean and degrease the thread in the cylinder pipe and cylinder head.
– Secure the thread by spreading three drops of Loctite 243 over the entire thread.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-11

– Attach the cylinder head and screw it on as far as it will go using a hook spanner. Secure the cylinder head into its final position by knocking the hook spanner with two blows of the hammer.
– Clean and degrease the thread in the cylinder pipe and fork clevis.
– Secure the thread by spreading three drops of Loctite 243 over the entire thread.
– Attach the fork clevis and screw it on as far as it will go. Secure the fork clevis into its final position by knocking it with three blows of the hammer.

How-to-Disassemble-Assembling-Cylinder-for-Still-RX20-Forklift-12

 

(Visited 45 times, 1 visits today)