Categories: Auto Repair

OPCOM VAXU-COM Reset Inspection Service Internal Light for Opel

This article show procedures of how to use OPCOM VAXU to reset service internal for Opel.

 

Preparations:

Newest OPCOM VAUX-COM All Version Free Download

OPCOM Clone

 

Cars

Corsa-C

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Service Interval Settings

Now enter the desired service interval reset.

 

Corsa-D

Possible displays:

  • InSP – service
  • InSp2 – bulp failure
  • InSP3 – remote control battery
  • InSP4 – water in diesel filter
  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Programming
  • Choose Service Interval Reset
  • Press the brake pedal
  • Choose Yes

The Service Interval Is Now Reset .

 

Meriva

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Service Interval Settings

Now enter the desired service interval reset.

 

Astra-G

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Service Interval Settings

Now enter the desired service interval reset.

 

Astra-H

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Programming
  • Choose Service Interval Reset
  • Press the brake pedal
  • Choose Yes

The service interval is now reset.

 

Zafira-A

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Service Interval Settings

Now enter the desired service interval reset.

 

Zafira-B

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Programming
  • Choose Service Interval Reset
  • Press the brake pedal
  • Choose Yes

The service interval is now reset.

 

Tigra-B

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Service Interval Settings

Now enter the desired service interval reset.

 

Vectra-C

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Programming
  • Choose Service Interval Reset
  • Press the brake pedal
  • Choose Yes

The service interval is now reset.

 

Signum

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Programming
  • Choose Service Interval Reset
  • Press the brake pedal
  • Choose Yes

The service interval is now reset.

 

Insignia

  • Press the brake pedal (keep pressed)
  • Press the SET / CLR button in the Driver Information Centre

 

Antara

  1. Turn the ignition key to ON/RUN with the engine off
  2. Fully press and release the accelerator pedal three times within five seconds
  • If the change engine oil light is not on, the system is reset.
  • If the light comes on again and stays on for 30 seconds at the next ignition

cycle, it did not reset. You will need to reset the system again.

 

Vans

Combo-C

  • Choose Body
  • Choose Instrument
  • Choose Programming
  • Choose Service Interval Settings

Now enter the desired Service Interval Reset value.

 

Vivaro

The Service Reset procedure should not exceed 1 and a half minutes to complete.

  • Turn on the ignition.
  • Press and hold the the accelerator fully
  • Press the brake pedal down three times
  • Release both pedals and wait 10 seconds

The service interval is now reset.

If it does not reset:

  • Test drive the car for at least 5 miles
  • Turn the ignition off for at least 60 seconds
  • Repeat the above procedure

Movano 2007 – …

The Service Reset procedure should not exceed 1 and a half minutes to complete.

  • Turn on the ignition.
  • Press and hold the the accelerator fully
  • press the brake pedal down three timesl
  • Release both pedals and wait 10 seconds

The service interval is now reset.

 

If it does not reset:

  • Test drive The car for at least 5 miles
  • Turn the ignition off for at least 60 seconds
  • Repeat the above procedure
auto

Recent Posts

JCB 3CX 4CX Backhoe Loader Engine Throttle Cable Removal and Replacement

JCB 3CX 4CX Backhoe Loader engine throttle cable is routed from the L.H. side of the…

23 hours ago

How to Replace Fuel Tank Breather Filter Element for Liebherr R9600 Excavator

Here is the instruction show you guide on how to replace fuel tank breather filter…

2 weeks ago

FENDT 900 Vario COM III B092 Boost Pressure/Temperature Sensor

FENDT 900 Vario COM III tractor Component B092 - Sensor, charge air pressure/temperature reports the boost…

3 weeks ago

Deutz EMR3 Engine Trouble Code 87 / 97 / FlFCD WATER IN FUEL Solution

Deutz EMR3 Engine Trouble Code 87 / 97 / FlFCD WATER IN FUEL Solution Error description…

3 weeks ago

Kubota L3301 L3901 Tractor Hydraulic Flow Test Guide

This instruction show you guide on how to perform hydraulic flow test for Kubota L3301…

1 month ago

Bendix AutoVue FLC20 Camera LDW Configuration by JPRO

This instruction show you guide on how to configure Lane Departure Warning for Bendix AutoVue…

1 month ago