Categories: Do It Youself

How to Enable Audi MMI Green Menu (Hidden Menu) by VCDs & Script

This article show a guide on how to use VCDs or Script to enable Audi MMI green menu(hidden menu)

Audi MMI Green Menu is used for several operations.For activate it you can do it with a VagCom cable VCDs or using script.

This guide is for enable green menu in 3G and 3GP but you can follow the same steps with other systems with this instructions:

MMI 2G [07-Control Head]=>[Adaptation-10]=>Channel 8=>set to 1
MMI 3G [5F-Information Electr.]=>[Adaptation-10]=>Channel 6=>set to 1
MMI 3GP [5F-Information Electr.]=>[Adaptation-10]=>Channel 6=>set to 1
RMC [5F-Information Electr.]=>[Adaptation-10]=>Channel 5=>set to 1
MIB Not available

 

Related Contents:

How to Update Audi MMI Map

How to Active Audi MMI Map:3G &3 GP

How to update Audi MMI 3G Firmware

 

Enable Audi MMI Green Menu by VCDs:

Open VCDS and inside “Select Control Module” click on “Select” button

Select module “5F”

Click on “Adaption-10”

Enter “6” for the channel and press the “Read” button

Now,inside the “New Value” field set the value to “1” and click “Test” and “save”

Note that only “Save” may be available in which case you would ignore the “Test” button Press “Done,Go Back”,close the controller and quit the software.

There no need to restart the MMI,just enter the hidden menu.

MMI 2G SETUP+CAR
MMI 3G SETUP+CAR
MMI 3GP CAR+MENU
RMC CAR+MENU
MIB Not available

 

 

Enabling Green Menu using a script

Download the”Green Menu” script

Format your SD in FAT32 and copy the script’s files in the SD root(like picture below)

Make sure that MMI is fully booted(press all buttons once RADIO CAR NAV MEDIA TEL)

Wait until all options are ok(no options in gray) even when all options are ok wait a minute more.

Is the moment for insert the SD in slot 1。

Don’t touch anything

After a few seconds screen will popup,press any key(we suggest thebig knob) once

Don’t touch anything again(the script are copying files and doing stuff)

After some seconds/minutes the script will finish and another screen will appear.

Remove the SD before doing anything

Reboot your MMI using the 3 button

Now you can access to “Green Menu”

auto

Recent Posts

MANITOU MT6034 Telehandlers PWP System Deactivation Tests

This instruction show you guide on how to do deactivation test for MANITOU MT6034 telehandlers…

3 days ago

How to Solve Liebherr Machine ECU2 P1119 SCR System Plausibility Error

This instruction show you guide on how to solve Liebherr machine ECU2 P1119-00 trouble code…

5 days ago

Bobcat Machine P18A5 Suction Line Heater Open Error Solution

This instruction show you guide on how to solve Bobcat machine trouble code P18A5 suction…

1 week ago

AGCO Machine SPN 102 – FMI 31 Intake Manifold Pressure Drop Too High at Cranking

The measured intake manifold pressure (signal from boost pressure sensor) is below the warning limit…

2 weeks ago

JCB 3CX 4CX Backhoe Loader Engine Throttle Cable Removal and Replacement

JCB 3CX 4CX Backhoe Loader engine throttle cable is routed from the L.H. side of the…

2 weeks ago

How to Replace Fuel Tank Breather Filter Element for Liebherr R9600 Excavator

Here is the instruction show you guide on how to replace fuel tank breather filter…

1 month ago