How to Do Key Coding Function for Fiat/Alfa/Lancia/Iveco by FiCOM

This instruction is show you guide on key coding function for Fiat/Alfa/Lancia/Iveco by FiCOM. Include Transponder coding,Remote controls coding, Immobilizer code etc.

 

Preparation:

FiCOM For Fiat/Alfa/Lancia Diagnostic software Free Download

How to Install and Quick Start FiCOM Diagnostic Software

 

Transponder coding

Coding transponders can be done by selecting the “Keys Coding” function. The procedure is as follows:

Activate function

Enter login code “ELECTRONIC CODE” from the CODE card

Insert all keys one by one into ignition according to program message. After inserting all keys will appear a window asking if you want to coding another key. If you answer yes, the program will wait to insert a new key again. Otherwise, it will save the loaded keys and display information about the end of encoding.

After you insert all keys one by one, end the coding routine.

You will be asked if you want to save transponder keys in memory. If you confirm the saving, you will delete all the keys that were not inserted into ignition during the operation and these keys will be not possible to coding in future again.

Previously deleted keys cannot be programmed again. Diagnostics can only add keys from system CODE2 and later (Megamos crypto + HiTag).

 

Remote controls coding

Operation works similarly as transponders coding.

 

Verification of coded keys

Value of  “Number of enabled keys” in measured values should be the same.

 

Immobilizer Code2

Code2 Bosch ST7 ?Philips Crypto?

Alfa 156 2003+

 

Code2 Bosch 93C5 Philips Crypto

Alfa 156 -2002

Alfa 166

 

Code2 Marelli  Megamos Crypto

Citroen Jumper

Citroen Relay 2001-2006

Fiat Ducato RST

Fiat Multipla

Lancia Lybra

Peugeot Boxer 2001-2006

 

Code2 Delphi Megamos Crypto

Citroen Jumper

Citroen Relay 2001-2006

Fiat Ducato RST

Fiat Seicento

Peugeot Boxer 2001-2006

 

Warning: key contains pre-programmed data for a specific vehicle (the dealer key).

Login

Key coding

Information about coded keys

Key deletion

 

Immobilizer Code2 Iveco Bosch

Transponder Philips Crypto, key contains pre-programmed data for a specific vehicle (the dealer key).

Key coding is not supported at this time.

 

 

Emergency start

This procedure allows you to start the engine in a situation, when it is not possible to recognize the key or in case of failure of immobilizer control unit. Starting the engine is possible after entering the electronic code via the accelerator pedal. Proceed as follows:

Turn the key in ignition to MAR.

After 2 seconds, the EDC warning light starts to blink.

Depress the accelerator pedal up to the stop and hold it depressed for 5 to 12 seconds.

EDC warning light starts to flash more slowly.

When the number of flashes equals to the first digit of electronic code, depress the accelerator pedal to the stop and subsequently release it (when depressing the accelerator pedal, the EDC warning light turns OFF ). Follow the same procedure for entering of remaining digits of the electronic code.

After correct entering of the code, the EDC warning light stops flashing (otherwise repeat the procedure). Contact your authorized service always for check the system.

 

Immobilizer Code

First generation of CODE control unit does not have a diagnostics, keys are coded by master key. The keys doesn’t contain data for a specific vehicle. It is not possible to code more than 7 keys.

Key coding

The function is available from menu of coding BODY COMPUTER control unit.

Login function is used to verify the PIN code from CODE card and to gain access to secure special functions (for key coding is not needed)

Procedure of key coding

Insert a red master key, turn on the ignition and turn it off immediately when immobilizer warning lamp goes off .

Remove the red master key and insert another key to coding within 10 seconds

Turn on the ignition and turn it off immediately when immobilizer warning lamp goes off

You can repeat procedure from point 2 and code other key within 10 seconds

When all keys are coded, end the procedure by inserting the master key and turning the ignition on and off when immobilizer warning lamp goes off.