Heavy Equipment Repair

How to Solve Caterpillar C9 Vehicle Speed Signal Invalid?

This instruction show you guide on how to solve Caterpillar C9 engine trouble code 36 PID 84-2 vehicle speed signal invalid.

What you need?

CAT ET 2026A

Cat adapter 3

 

 

The Engine Control Module (ECM) detects the following conditions:

The “VSL Protection” is not programmed to the programmed “TEL”.

The vehicle speed is constant when the engine parameters indicate that the vehicle speed should be changing.

 

Engine speed is greater than 950 rpm for more than 60 ms.

 

Note: This code typically occurs when someone has tampered with the vehicle speed signal

For these vehicles, the vehicle speed signal is provided by an electronic source.

The signal is received over a single wire that is connected to ECM vehicle harness connector J1/P1-32 (vehicle speed in positive).Do not make any other connection to this line. A speedmeter hat should not be made to this line.For this type of signal. the ECM vehicle harness connector J1/P1- 33 vehicle speed in negative) must not be connected to the ECM in order to prevent introducing electrical noise into the circuit.

 

For vehicle speed problems on trucks that are equipped with either of these vehicle speed sources,first inspect the wiring from the electronic source to the engine ECM for open circuits or for short circuits.

 

The ECM can be configured to receive vehicle speed information from an electronic transmission control unit via the J1939 data link.The transmission must be capable of supporting the “)1939 ETC1 Broadcast Message (PGN 61.442 Bytes 2 & 3)”.This message provides the speed of the transmission output shaft. This feature requires the hardware for the 1939 data link to be installed in the chassis of the vehicle.This also requires a transmission that is electronically controlled and capable of supporting the necessary J1939 protocol.

 

When the engine is configured for the J1939 option, the circuit for the ECM vehicle speed input (terminals 32 and 33) will be ignored. The ECM uses the “Vehicle Speed Cal (J1939-Trans)” parameter value in order to calculate vehicle speed. The ECM uses the parameter value and the speed of the output shaft that is received over the J1939 data link to calculate the vehicle speed. The “Vehicle Speed Cal (J1939-Trans)” parameter is based on the revolutions per mile of the output shaft. There are several methods that can be used to arrive at this calibration value. Refer to Troubleshooting, “Vehicle Speed Circuit – Calibrate” for details.

The ECM can be configured to receive vehicle speed information from the Anti-lock Brake System (ABS) via the J1939 data link. The ABS must be capable of supporting the “J1939 High Resolution Wheel Speed Broadcast Message (PGN 65134 Byte 5-8)”, which provides wheel speed from the two rear wheels. The ABS will broadcast the assumed tire revolutions per mile.

Regardless of the source that is used to determine vehicle speed, the ECM uses the calculated value for the vehicle speed in the same manner to control several features and functions. The diagnostics for vehicle speed function similarly when either a hard-wired signal is provided to the ECM from a speed sensor, or a message is sent to the ECM via the J1939 data link. If the ECM detects a loss of vehicle speed or a value that is invalid, a fault code will be logged in order to alert the operator or the technician of the presence of a problem.

Probable Causes:

ECM Connection

Speed not calibrated properly in ECM

Vehicle Speed Sensor

Vehicle Speed Sensor connection/harness

Failed ECM

 

More repair case for Caterpillar machine,please refer to:Caterpillar Machine Repair

auto

Recent Posts

How to Solve Liebherr Machine Power or Speed Reduction?

How to solve Liebherr machine trouble code P1188 power or speed reduction emission related failure.…

1 day ago

Doosan Machine Timeout Error of CAN Receive Frame AUXIO1

Here show you guide on how to solve Doosan machine Timeout error of CAN receive…

1 week ago

Liebherr Machine Emergency Stop-Ignition on While Emergency Stop is Active

This instruction show you guide on how to solve Liebherr machine emergency stop ignition on…

2 weeks ago

How to Solve Doosan Machine U043D CAN Receive Frame Counter Error

This instruction show you guide on how to solve Doosan machine trouble code U043D message…

3 weeks ago

AGCO Machine Trouble Code SPN 1485 – FMI 03 Solution

Here is the instruction show you guide on how to solve AGCO machine trouble code…

4 weeks ago

Detroit DD13 J1939 Wheel-Based Vehicle Speed Sensor Signal Missing

Detroit DD13 EPA10 (2010-13) trouble code SPN 84 FMI 13 (MCM) J1939 Wheel-based vehicle speed…

1 month ago