How to Use Zed-Full Program Key For Fiat Egea (OBD Can’t Support)

This illustration show you guide on how to use Zed-Full programmer to add new key for Fiat Egea.And for more Zed-Full cases,please check here:Zed-Fll Test Feedback

 

Note:If your Fiat BSI module can support pre-coded by OBD,check procedures here: How to Use Zed-Full Program Keys for Fiat Egea by OBD

 

Procedures:

Connect Zed-full to Fiat Egea OBD port

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (1)

Enter menu to select OBD application

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (2)

Select “Fiat”–>”Fiat-EU”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (3) How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (4)

Select “Immobiliser”–>”Pre-coding chip”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (5)

 

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (6)

Select system “Delphi Meg.AES chip NEC MCU”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (7)

Turn ignition ON then press “Continue”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (8)

Current,reading car data from BSI through OBD is not supported.Please follows these steps respectively;

1.Remove BSI module from the car and use 265the eeprom module to get required car datat

2.Inert BSI module back to car and follow OBD key programming steps

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (9)

Remove BSI unit which is just under the steering wheel

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (10)

You must solder 1KΩ Resistor between blue and red cables of the ZFH-C07/ZFH/C07-2 cable

After eeprom/MCU application BSI unit must be reinstalled to the vehicle and new key should be programmed via OBD

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (11) How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (12)

Back main menu to select “Eeprom and MCU”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (13)

Select “Fiat”–>”Module 265 NEC D70F3556…”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (14)

Clcik “App.Info”,you may see more details

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (15)

Connect ZFH-C07 cable socket to Zed-FULL

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (16)

Press “Continue button”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (17)

Select Eeprom or MCU type to be read from the list and press “Continue” button

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (18)

Select “Read In Circuit”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (19)

Ensure that all wire and socket connection are OK and press “Read” button

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (20) How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (21)

Reading Eeprog/MCU is successful.Zed-Full programmer will keep the car data on its internal memory.Process will continue with OBD application on car.

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (22)

Desolder ZFH-C07 cable wires from BSI and insert unit back to the car

After then select “OBD application”–>”Fiat”–>”Fiat ECU”–>”Immobiliser”–>”Pre-coding”–>”Delphi Meg.AES chip NEC MCU” respectively.

Then turn ignition ON and press “Continue” button

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (23)

Connection is successful!

Car VIN number,pin code and key ID will be shown on Zed-Full screen

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (24)

New key to be programmed must be precoded first.

Press “Continue” button

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (25)

Put new key to be precoded to Zed-Full antenna and press “Continue” button

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (25)

Pre-coding written

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (27)

Press “No” to exit transponder precoding procedure

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (28)

Press “Continue” button to program precoded transponders to the car

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (29)

All non-programmed working key will be erased from cacr memory irreversibly and can not be programmed again.

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (30)

Car has two working keys,we will add 1 key,so we enter 3 as total key quantity

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (31)

Working key was already on ignition and ignition was “ON”,press “Continue”

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (32)

1st key is on ignition,press “Continue” button

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (33)

Put 2nd key to ignition and press “Continue” button

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (34)

Put new key to be programmed (3rd key) to ignition and press “Continue” button

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (35)

Programming successfully!

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (36)

Now you can test all programmed keys

How to Use Zed-Full Program Key For Fiat Egea (OBD Can't Support) (37)

 

More FIAT key programming,check this article collection:Fiat Key Programming

Visited 1 times, 1 visit(s) today