Categories: Auto Coding

FSC Code Solution for BMW E and F Series CIC

This article focus on FSC code solution for BMW E and F series CIC head unit.And for NBT check this article:How to generate BMW NBT & CIC FSC code .

 

Preparations:

BMW E-sys software Free Download

BMW FS-Tool Freischalt tool Free Download

 

How to install Head Unit patch

1.Copy provided copie_scr.sh file into any available USB flash memory stick with FAT32 file system. Recommended flash drive capacity is 2 or 4 or 8 GB.

2.Turn ignition on or better start engine.

3.Wait at least 60 seconds for full system boot and then connect the USB flash drive.

4.After 5-10sec iDrive system will reboot

5.Disconnect USB flash drive and wait at least 60 seconds for full system boot.

 

How to import custom FSC codes in E series CIC

1.Configure EDIABAS for D-CAN or K-line protocol, perform CIC coding using NCS-Expert tool with correct car FA and original VIN.

2.Unpack provided archive with FSC codes.

3.Start FS-Tool2 and establish connection.

4.Open “Configuration” tab, press “Search” button for “Sig Certificate” and open “SIG.der” filefrom unpacked archive.

5.Press “Search” button for “FSCS Certificate” and open “00170001.der” file from unpacked archive.

 

6.Open “SWT Develop” tab, select “STORE_SIG_CERT” job and press “=>” button. Do same for “CHECK_SIG_CERT” job.

 

7.Press “Execute” and check for two “successful” statuses.

8.Clean right window via select each line and press “<=” button.

9.Open “Parameter” tab and enter original car VIN.

10.Go back to “SWT Develop” tab and add “SET_VIN” job.

11.Press “Execute” and check for “successful” result.

12.Clean right window via select each line and press “<=” button.

13.Add “STORE_FSCS_CERT”, “CHECK_FSCS_CERT”, “STORE_FSC”, “CHECK_FSC” jobs. Press ”Load from…” button for “Freischaltcode:” and select “00170001.fsc” file from unpacked archive.

14.Press “Execute” and check for four “successful” statuses.

15.Repeat same for “00190001.fsc”, “001B0001.fsc”, “006F0001.fsc”, “009B0001.fsc”, “009C0001.fsc” files and check results every time.

16.If requested, enter map code from 002800**.fsc file via iDrive menu or via FS-Tool2 “STORE_FSC”,“CHECK_FSC” jobs.

 

How to import custom FSC codes in F series CIC

1.Start E-Sys, establish connection and perform CIC coding with correct car FA and original VIN.

2.Open “FSC-Extended” page in “Expert Mode” tab, enter “0x63” in “Diagnostic Address(hex):” and press “Identify” button. After few seconds “HU_CIC” should appear in “Base Variant:” field.

3.Select “WriteDataByIdentifierVIN”, press “>>” button, enter real long car VIN. Press “Start” button and check Log window for “ok” result.

 

4.Remove “WriteDataByIdentifierVIN” from left window via selecting this line and press “<<” button.

5.Unpack provided archive with FSC codes. Preferably in C:\DATA\SWT folder.

6.Select “StoreSIGCert”, press “>>” button and open “SIG.der” file from unpacked archive.

7.Select “CheckSIGCert”, press “>>” button. Enter “0x1B” into “Application number (hex/dec)” field and “0x01” into “Upgrade index (hex/dec)”. Press “Start” button and check for two “ok” results.

8.Remove “StoreSIGCert” and “CheckSIGCert” from right window via select each line and press “<<” button.

9.Select “StoreFSCCert”, press “>>” button and open “001B0001.der” file from unpacked archive.

 

10.Select “CheckFSCCert”, press “>>” button. Select “StoreFSC” and press “>>” button. Select “CheckFSC” and press “>>” button.

11.Press “…” button and select “00170001.fsc” file from unpacked archive. “Application number (hex/dec)” and “Upgrade index (hex/dec)” fields will be adjusted automatically according to opened file.

 

12.Press “Start” button and check for four “ok” results. Repeat same for “00190001.fsc”, “001B0001.fsc”, “006F0001.fsc”, “009B0001.fsc”, “009C0001.fsc” files and check results every time.

13.Clean right window via select each line and press “<<” button.

14.Now select “GetStatus” at left window, press “>>” and “Start” button. In Log window scroll up and check “FSCSCertStatus” and “FSCStatus” for every code to be “accepted”. Code “AppNr./UpgrIdx 40(0x28)” is short map update code, which is generated from 0x1B code and it’s “Upgrade Index” depending to used map data. It could have “rejected” state, then you need to get new map update code.

 

CIC FSC Codes Application number List

0017 – Voice control

0019 – Navigation system Professional

001B – Navigation system Professional

0028 – European Map Code

006F – Satellite Tuner

009C – BMW Apps

auto

Recent Posts

How to Solve Liebherr Machine Power or Speed Reduction?

How to solve Liebherr machine trouble code P1188 power or speed reduction emission related failure.…

5 days ago

Doosan Machine Timeout Error of CAN Receive Frame AUXIO1

Here show you guide on how to solve Doosan machine Timeout error of CAN receive…

2 weeks ago

Liebherr Machine Emergency Stop-Ignition on While Emergency Stop is Active

This instruction show you guide on how to solve Liebherr machine emergency stop ignition on…

3 weeks ago

How to Solve Doosan Machine U043D CAN Receive Frame Counter Error

This instruction show you guide on how to solve Doosan machine trouble code U043D message…

4 weeks ago

AGCO Machine Trouble Code SPN 1485 – FMI 03 Solution

Here is the instruction show you guide on how to solve AGCO machine trouble code…

1 month ago

Detroit DD13 J1939 Wheel-Based Vehicle Speed Sensor Signal Missing

Detroit DD13 EPA10 (2010-13) trouble code SPN 84 FMI 13 (MCM) J1939 Wheel-based vehicle speed…

2 months ago